Welcome to Tesla Motors Club
Discuss Tesla's Model S, Model 3, Model X, Model Y, Cybertruck, Roadster and More.
Register

Recent content by M_VdM

  1. M

    What is the RS-485 port for on a Gen 3 Wall Connector?

    That little connector serves NO purpose. For the moment, the components (U12?) for that RS-485 interface are not populated ... See this THREAD for more info & photos.
  2. M

    Gen3 HPWC disassembly, with overheating issues explained!

    Anyone noticed the RFID-antenna on that LED-strip/RFID Flex-PCB [1470138-61-D] ? Furthermore: looks like the components (U12?) for that RS-485 connector are not populated ...
  3. M

    Anyone know what this model is?

    Faraday Future FF 91
  4. M

    DIY laadpaal

    Kijk misschien ook even naar onderstaande projectjes: dsPIC33EP_IEC61851_J1772_ChargePort_EVSE: A prototype IEC61851 / J1772 EVSE Interface intended to connect to a 3.3V microcontroller of your choice. TWCController: Wireless Controller for a Gen 2 Tesla Wall Charger (hardware and software)...
  5. M

    Rempedaal effect op ramen?

    Inderdaad ! Staat vermeld in de sectie " 'Best practices' bij koude weersomstandigheden" op p. 101 v/d handleiding. • Model 3 past de stand van de ruiten automatisch iets aan, zodat het openen van portieren bij lage temperaturen wordt vergemakkelijkt.
  6. M

    Logo’s radiozenders

    Ook zo in België ... Ik dacht dat zenderlogo's een wezenlijk onderdeel uitmaakten van de DAB+ standaard ?!?
  7. M

    Tesla Wall Connector load sharing protocol

    @hcsharp: Would you mind sharing your code with us ?
  8. M

    Tesla Wall Connector load sharing protocol

    Answer: ———————————————————————————————————— Get firmware version: FB1B Response: FD 1B 04 05 03 00 00 00 00 00 00 00 00 27 Decoded response Firmware version: 4.5.3 ———————————————————————————————————— Get (S)TSN (serial number): FB19 Response: FD 19 41 31 38 47 30 30 30 XX XX XX...
  9. M

    Tesla Wall Connector load sharing protocol

    Finally got my own brand new TWC ... :D:cool: Noticed that the EU-version has an extra connector / jumper "CNA4" near the bottom edge of the PCB: Pin 1 --> UA21 pin 74 = GPIO 34 (with a pull-up resistor) Pin 2 -- Gnd See this TMC post a for picture. @CDragon : can you find a trace of that...
  10. M

    HPWC data link question

    Have a look over here: HPWC Hacking
  11. M

    Tesla Wall Connector load sharing protocol

    Great Job ! I suppose you 've been performing all this testing/probing with the TWC 's DIP-switch 2 in the UP position (=Default) ? What if you put that one in the DOWN position ? Apparently, that puts this EVSE in a more generic J1772 mode - not using any (Tesla proprietary) CAN-bus...
  12. M

    Tesla Wall Connector load sharing protocol

    @tga: Be carefull not to mix "HPWC" (old Gen I) and "TWC" (new Gen II) devices in this sort of discussions. Before you know, people are talking about completely different hardware ...;) Of course: all info is welcome !
  13. M

    Tesla Wall Connector load sharing protocol

    Tja ... for the Dutch / LaadSlim customers ... Not for me ... sniff (pun intended) :rolleyes:
  14. M

    Tesla Wall Connector load sharing protocol

    If only we could sniff a Maxem® ...
  15. M

    Tesla Wall Connector load sharing protocol

    Noticed these power-related "mods" too ... Be careful there ! Especially make sure you don't create a ground loop between the TWC (=DUT) and your "testing equipment".

About Us

Formed in 2006, Tesla Motors Club (TMC) was the first independent online Tesla community. Today it remains the largest and most dynamic community of Tesla enthusiasts. Learn more.

Do you value your experience at TMC? Consider becoming a Supporting Member of Tesla Motors Club. As a thank you for your contribution, you'll get nearly no ads in the Community and Groups sections. Additional perks are available depending on the level of contribution. Please visit the Account Upgrades page for more details.


SUPPORT TMC
Top