Separate names with a comma.
It's not a major job and can be relatively easily done...(I know, I've done it twice...first time the new insolation I used was too thin) Every...
This is an insulation failure. Easy fix...Read in the thread PEM failure....If you are not wanting to do the job yourself contact Gruber...
Hey Mate good job...curious about the resistors as well...did you use 1mm ceramic or did you find something a little thicker? BTW Tesla want me...
If its charging it means your repair was good and your insulation is fine...I had a blown fuse on the little megapole board as PG says...top left...
No I have not looked at it yet....its on my list....I think I have to take the dash off...not 100% sure...not the end of the world but a bit of a...
Yeah, and then it becomes their fault if you toast yourself because they would not sell you one....:eek:
I spoke to Matthieu the other day and he related the story - I also called the SC in question (for all together another reason)- where I had...
As Daniel said it could be a temp sensor...if I remember correctly it seemed possible to connect the sensor connector either way. I used the way...
Add me to the signature...now learnt about repairing PEMs....I guess I should thank Tesla for that...o_O
Hello there - I'm not able to access the links....it says I don't have permission....
Just looked at the specs on this product...the thermal conductivity seems worse than OEM...
Yes I would absolutely state this to prospective buyer - in any event should it fail again, its a relatively easy fix. Worst case you may have to...
If you could go for 1.5mm I think it would give a better margin of safety... I have no idea what the factory clearance was but what I do know is...
I have 1mm ceramic strips which for the moment seem fine - the 0.63mm strips that I used earlier were not fine. Its important for the IGBT's that...
I would use something similar to this.... BlueMagic
A couple of things...AFAIK there is also a torsion bar that needs to be changed and secondly I thought they were changing these fans out for free...
Thank you very much... all arrived in France - not sure when - have not checked the letter box in some days...but they look great - thanks a lot!
Although it looks bad there is nothing too dramatic here - again it is the failure of the insulation that has caused this...change out the IGBT's...
Difficult from my side of the pond to get your head around this...I just feel so desperately sorry and sad for the poor folk currently in so much...
Hi Rolf - I had the same problem - there is somewhere in the menu to reduce the volume - I have changed the unit out for an Android unit now...but...
I would also love 1 of each....fantastic - will PM address details...
Peter Gruber is probably the safest choice - he's done many more of these than probably anyone except Tesla (I'm not even Tesla do them) but if I...
The reason for point number 2 is to provide some extra security for you so there is no possibility of stray currents, and secondly if your ESS is...
Yeah really cool...saw it somewhere else on the site... if something goes pop - you might see the plasma baby....without going off subject where...
Yes the torque was ok - that's for sure but 0.63mm was not a good idea...but this is part of the progress in getting it sorted. I think I dodged a...
Yes just the finest smear of paste on the IGBT's...see attached photo... I have now re positioned the strips so the IPGT's are much more centrally...
A bit of an update on my PEM...I took it apart yesterday in situ - quite easy with the rear wheels on ramps otherwise my back would have been a...
Yeah...I'd like 1 that looks good to go on the rear bumper....radio is cool but it would not make the radio any more practical...
I have written a reply but the number of characters here is limited. Email me on [email protected] Jonathan
I"ll reply tomorrow...
Did not see anything on the 2.5 boards when I had them apart - I will be doing a little pre-emptive surgery next weekend and will double check...
I found 1 of these under my seat when I took them out for cleaning...
Thanks - some interesting information - we all need to be vigilant to make sure we don't go here but if you do...its nice to know there is a...
I have just tried to wiggle around with my finger inside the latching mechanism (pointing out) and eventually it comes out easily - I have had...
Its inside the left rear wheel well. It totally isolates the battery from the car. Its an orange plug with a lever to lift up and then remove....
I received this mail from Hologram yesterday.... Hello, We wanted to reach out and let you know about a change to our phone number policy that...
Thanks Kerios - I'll try that but I think I need to remove the centre consul to get the panel off...I'll try from the outside first...
Thanks for this...switch first place to check....if I remember correctly whole dash and stereo needs to be removed first before I can get to the...
No, no fan on position 1 no matter where the direction is - ok seems this is not normal. OK now to get to the bottom of this...any gems? I must...
Thanks, yes zero is of course off - but on my car there is no fan running on position 1. Only position 2 & 3. Just does not seem normal to me?
Hello, I don't get any air from position 1 on the fan control. Everything lights up ok - only get fan running on speed 2 or 3. Assume...
I think they will rival Tesla in a few years, but then just as they release their offering Tesla will move the goalposts again. However Tesla...
Really sorry to hear of your troubles...I'm sorry I don't know enough to help you but I have found a little with the error message... BSM: V_ess...
Sounds good to me...waiting with patience...
If the lever is not in place and down you will get "BMS Contacter error" and the car is not going anywhere...
I've got a rooted Android unit and blown away by the amount of customisation...sound is great (got the upgraded sound system) When the source is...
Congratulations on your job....for sure its a great feeling of accomplishment...yesterday I had a long chat with Daniel re his PEM...When you do...
Its hard to know with the OEM insulation...they put a past down and screw the IGBT's into that... The material that some people are using now is...
Out of interest I went for a drive yesterday...it was probably only 13º or 14º C outside gave the car quite a lot of hard accelerations - the PEM...
Well I spoke to my supplier about Aluminium Nitrate...he said it is less fragile - which is good - better thermal conductivity (also good) but he...