Welcome to Tesla Motors Club
Discuss Tesla's Model S, Model 3, Model X, Model Y, Cybertruck, Roadster and More.
  • Want to remove ads? Register an account and login to see fewer ads, and become a Supporting Member to remove almost all ads.
  • The final cut of TMC Podcast #34 is available now with topics timestamped. We covered Tesla's rollercoaster prices, Toyota pushing junk science, Mike's new Model 3, Optimizing track mode for snow driving, FSD V11 apparently coming by the end of this week, and more. You can watch and check out the chat replay on YouTube.

Search results

  1. Matte3

    Oregon License Plate Lookup

    https://dmv2u.oregon.gov/eServices/_/#1 If the link makes you "start over", its the 3rd option down from the "registration" tab which is located in the center of the page towards the top..
  2. Matte3

    Model 3 Roof Rack Brand New

    Can you send me a private message? I can't seem to find out how..
  3. Matte3

    Model 3 Roof Rack

    Could you send me a private message? Can’t seem to figure out how.
  4. Matte3

    Best Adhesive for Model 3 spoiler?

    You just need 1/2" on the sides. I use a 1" roll and cut it in half after cutting the entire length I need and use each half for each side. Hope that makes sense.
  5. Matte3

    Best Adhesive for Model 3 spoiler?

    We do a lot of XPEL wraps at my shop and so we need to remove the factory spoiler quiet often and install it back on after the wrap. I have not seen one factory installed one that sits nice and flush against the trunk. The ends are always lifted. We remove the factory double sided tape and...
  6. Matte3

    Anyone recommend a shop PDX/Vancouver area to lower model 3?

    Yes, the aligned it as well. They also installed new tires and wheels for me. I understand the drive, but since they are experienced on these cars and specialize in race car suspension on a daily basis, I wouldn't trust anyone else with it.
  7. Matte3

    Anyone recommend a shop PDX/Vancouver area to lower model 3?

    I recommend AR Motorsports in Tigard, OR. They lowered my 3 on Motion Control Suspension
  8. Matte3

    Pic of your Model 3.......RIGHT NOW! [model 3 pictures thread]

    Yes, it is very similar to nardo gray. We wrapped it and also applied XPEL PPF on the full front and rockers to preserve the wrap against rock chips damage!
  9. Matte3

    Lowering the Model 3

    Lowered on Motion Control Suspension (MCS)
  10. Matte3

    Is this within spec? Hood emblem off-center

    If you really want to see if its aligned straight on the hood or not, open the frunk and eye the line of the emblem to the latch!
  11. Matte3

    Burn marks on white seats from seat heater?

    I have the same issue, been meaning to ask service about it.
  12. Matte3

    Signature Black wall charger.

    Can you send me a message with your contact number? I can't seem to figure out how to send a message. Thanks
  13. Matte3

    WHITE interior with creases/wrinkles (brand new)

    Don’t be surprised if they work themself out. When I picked mine up I had a crease on the back seat that looked similar to your driver seat and it went back to its original state after a couple days.
  14. Matte3

    FS: Model 3 lifting/jack pad

    I'm not capable of sending a PM, maybe because my account is new? Can you please contact me. I would like a set of 4 of the version 2. Let me know if you can not send me a PM..
  15. Matte3

    3D Maxpider Kagu Mats for Model 3

    I found the 3D mats from 1010 tires for $189 shipped. Should be receiving mine today. Placed the order 4 days ago.. Here is the link. Kagu-Floormat 3D MAXpider Kagu Car Floor Mat
  16. Matte3

    Tesla Wall Connector Installation

    I am not comparing apples to apples. It does not require a electrician to take on this job. For example I'm not going to install a roof on my house.. There are some things we all can and are capable of doing without hiring a professional. I didn't ask how to wire up the connector to the panel or...
  17. Matte3

    Tesla Wall Connector Installation

    Thank you all for the help. To be honest maybe I sounded like I didn’t do any research etc before starting this thread but I have. I’m just that guy that reads 50 times before doing something. I basically had to directly ask and get the answer for myself . Anyway, again I know working with...
  18. Matte3

    XPEL Stealth or Matte PPF on Solid Black or Obsidian Black?

    There is definitely a difference. We just wrapped a solid black Model 3 last week at my shop and we will be wrapping a model x in obsidian black next week. The metallic flakes definitely still show through the stealth PPF under the sun. I personally like it better on solid black..
  19. Matte3

    Tesla Wall Connector Installation

    So anyone who asks a question should keep it to themself and call a professional? Lol. I understand working with electrical is not a joke and the risks that come with it. I’ve done other type of electrical work and just want to confirm the type of wire on this specific project.
  20. Matte3

    Tesla Wall Connector Installation

    Hello everyone, I am going to be installing the wall connector myself but want to confirm what wires to go with in what type of conduit. I am going to run around 35' feet as I will be installing the wall connector on the opposite side of my garage that the breaker box is on (two car garage door...

About Us

Formed in 2006, Tesla Motors Club (TMC) was the first independent online Tesla community. Today it remains the largest and most dynamic community of Tesla enthusiasts. Learn more.

Do you value your experience at TMC? Consider becoming a Supporting Member of Tesla Motors Club. As a thank you for your contribution, you'll get nearly no ads in the Community and Groups sections. Additional perks are available depending on the level of contribution. Please visit the Account Upgrades page for more details.