Welcome to Tesla Motors Club
Discuss Tesla's Model S, Model 3, Model X, Model Y, Cybertruck, Roadster and More.
Register

Sold Model 3/Y Forged 19x10 ET35 wheels

This site may earn commission on affiliate links.
Status
Not open for further replies.
I had an extra set of Forged wheels custom made: 19x10 ET35 with 950kg load rating. Wheels sit flush on MPP/Girodisc rotors and 275/35/19 PS4S tires on my M3P. Factory M3P rotors will push wheels inboard 4mm and may require spacers depending on tire size.

Turns out I have too many wheels now, so I'm putting them up for sale. They took 3 months to get to me, and I drove them for the summer (approx 4k miles). No bends or scratches. Each wheel weighs approximately 24-25 lbs.

Wheels only for sale (tires and TPMS have been removed). Boxed and ready to ship.

Asking $2000. Add $150 for Genuine BBS center caps.
 

Attachments

  • PXL_20220808_211442425.jpg
    PXL_20220808_211442425.jpg
    974.4 KB · Views: 502
Last edited by a moderator:
Here's what they look like on the car and 275/5/19 PS4S tires.
 

Attachments

  • original_f552c911-b204-4f36-97e0-126387d21dab_PXL_20220809_152930789.jpg
    original_f552c911-b204-4f36-97e0-126387d21dab_PXL_20220809_152930789.jpg
    551.6 KB · Views: 369
  • original_a8e627b2-e6ef-4a81-990c-baca3804f170_PXL_20220809_153255364.jpg
    original_a8e627b2-e6ef-4a81-990c-baca3804f170_PXL_20220809_153255364.jpg
    409.8 KB · Views: 350
Interested but it's hard to commit with such limited info. I mean no offense but can you post some sort of evidence about any ratings that they meet? Also evidence they are truly forged and not "flow forged" or other words that some manufacturers use. I'd hate to break or bend one at the track..
 
I wish I could give evidence of the load ratings, but as far as Forged vs Flow Forged, they showed me the cut wheel before powder coating. So, I 100% believe they're forged. Could they just show me anything? Probably, but the raw aluminum flow forged/cast wheels look VERY different from forged wheels. Attached photos of the pre-powder coated wheels for you to see.

The load rating is in their CAD drawing, so I took their word for it. They were originally going to go with 750kg, but I mentioned these being track rated. So, the engineer said it'd have to have thicker spokes for increased load rating, resulting in a heavier wheel. It would've weighed around 20lbs (less than 10kg) at 750kg load. Upping it to my desired load rating added a few pounds due to thicker spokes and such (11kg - 11.5kg during the planning, then the CAD design came back with about 11kg estimate). That part is purely faith.

I posted the CAD drawing for you.
 

Attachments

  • Screenshot_20221210-144945.png
    Screenshot_20221210-144945.png
    465.9 KB · Views: 127
  • IMG-20220601-WA0000.jpg
    IMG-20220601-WA0000.jpg
    103.9 KB · Views: 115
  • IMG-20220601-WA0001.jpg
    IMG-20220601-WA0001.jpg
    111.8 KB · Views: 143
  • Like
Reactions: gtmotor and santua
Status
Not open for further replies.