Matte Black License Plate frame suggestions.

[Glamisduner]

I was trying to install a black license plate frame from a recommendation from someone on the forum.
However I found the back of the frame has an edge with nothing to soften it. Directions suggest using weatherstripping to prevent marring the paint, but the model 3 is curved so this proves a challenge.

This is the one I was trying to install:
https://www.amazon.com/gp/product/B01N3LBH1S/ref=ppx_od_dt_b_asin_title_s01?ie=UTF8&psc=1

I'm looking for other options: So far all I have found is this one:
https://www.amazon.com/gp/product/B07CV5PLFM/ref=ox_sc_act_title_1?smid=A1C5JY3DCAHLSG&psc=1

 

[Lifeinabox]

I’m not a fan of license plate frames but tried this based on a recommendation on the forum. Pretty happy with it and no worries about scratches or rust.

https://www.amazon.com/Rightcar-Solutions-Flawless-Silicone-License/dp/B07CV5PLFM

 

[mrau]

I got the grey silicone frame that @Lifeinabox linked from Amazon. Minimalist look and great protection for car from the sharp edges of the plate. Looks good on MSM color.

 

[Glamisduner]

I got the grey silicone frame that @Lifeinabox linked from Amazon. Minimalist look and great protection for car from the sharp edges of the plate. Looks good on MSM color.

hah yea, that's the second one I linked too. Just put them on my wife's volvo. I guess that's the one to get then for people that are paranoid like me.

 

[mrau]

Oops, guess I missed your second link @Glamisduner .

Also, I added some black screw covers from Amazon. Worked great with the factory license plate screws.

https://www.amazon.com/gp/product/B00032KC3K/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1

 

[JPP]

OP--I have the same frame on my 3--see avatar.I have the 'gen 1' rear license plate mount on my P3D+ (4 plastic inserts, no separate mounting plate). I sort of recall the DFDM black frame coming with some peel-and-stick pads but these were thin. I had a roll of 3M VHB double sided automotive tape (meant to mount trim and the like):

https://www.amazon.com/gp/product/B01BT0A6MG/ref=oh_aui_search_asin_title?ie=UTF8&psc=1

So I cut some small pieces to use as pads behind the black frame and the license plate. All good.

 

[forkee]

amazon. 2 for $10

https://www.amazon.com/gp/product/B018FUYN0O/ref=oh_aui_search_detailpage?ie=UTF8&psc=1

 

[Glamisduner]

OP--I have the same frame on my 3--see avatar.I have the 'gen 1' rear license plate mount on my P3D+ (4 plastic inserts, no separate mounting plate). I sort of recall the DFDM black frame coming with some peel-and-stick pads but these were thin. I had a roll of 3M VHB double sided automotive tape (meant to mount trim and the like):

https://www.amazon.com/gp/product/B01BT0A6MG/ref=oh_aui_search_asin_title?ie=UTF8&psc=1

So I cut some small pieces to use as pads behind the black frame and the license plate. All good.

Interesting, I played with thatframe and testing weatherstripping tape for about an hour then decided to just put it on my truck instead. No matter what I did the center wanted to rub the paint I think due to the curve on the back of the 3, although it would probably be ok I guess. It also scratched my plate a little, the nubs that the screws go through jabbed into the reflective paint near the bottoms of the numbers. I also scuffed the paint removing it from the factory plate holder (should have been more careful oops!) Oh well. I should have just left it alone!

 

[Glamisduner]

Has anyone tried the weathertech frames? Do they work with the supplied hardware?

 

[Glamisduner]

What about the weathertech bumper frame for the front?

Is are the weathertech clear cover frames illegal in CA?

 

[YisSerL]

What about the weathertech bumper frame for the front?

Is are the weathertech clear cover frames illegal in CA?

Yes, the clear cover frames are still illegal in CA. SB-712 was suppose to change the law so you can, but that was rejected.

California says no, you can’t cover your license plate

 

[Glamisduner]

Yes, the clear cover frames are still illegal in CA. SB-712 was suppose to change the law so you can, but that was rejected.

California says no, you can’t cover your license plate

Thanks! Guess that means I'm either getting the weathertech bumper plate frame for the front or one of them silicon jobs.

 

[mrbcc]

I bought some adhesive backed foam sheets and cut to size on the back of my plate. Works great, no rattling, no scratching, very minimalist.

 

[YisSerL]

I use the silicon one that @Lifeinabox mentioned earlier.

I was surprised that it works well.

 

[Glamisduner]

I use the silicon one that @Lifeinabox mentioned earlier.

I was surprised that it works well.

white or black for the front / back on a white car?
They are currently sold out of black.

 

[Prunesquallor]

I’m not a fan of license plate frames but tried this based on a recommendation on the forum. Pretty happy with it and no worries about scratches or rust.

https://www.amazon.com/Rightcar-Solutions-Flawless-Silicone-License/dp/B07CV5PLFM

I just put these on my M3 and I really like them. The whole back is silicone and it snugs right up to the truck. No hint of rattle. I have “The Bandit” plate mount on the front and the frame is snug and flat against it.

Very happy.

 

[Gator Rican]

Anyone tried these?

Tesla MODEL 3 # Black License Plate Frame Free Security Screws, Laser Engraved, Metal, No Stickers, Free Ship from CA, Free Returs

 

[SoCalLawyer]

Hi gator I actually custom make them those plates people have been requesting many different designs which you see on the shop and those screws were a headache to source but I finally found them. Try out a set and here’s a pic of a recent review

 

[Gator Rican]

Hi gator I actually custom make them those plates people have been requesting many different designs which you see on the shop and those screws were a headache to source but I finally found them. Try out a set and here’s a pic of a recent review

Hi, I am concerned about durability - rust and powder coating coming off. Doesn't seem like anyone has had them long enough to report on this. Also are they 100% Stainless Steel or aluminium?

 

[hocr]

I’m not a fan of license plate frames but tried this based on a recommendation on the forum. Pretty happy with it and no worries about scratches or rust.

https://www.amazon.com/Rightcar-Solutions-Flawless-Silicone-License/dp/B07CV5PLFM

Got the same! Nice and simple