Gtr wheels for model y

[Aznvietboy725]

I'm planning on buying 2012-2016 gtr 10 spoke wheels for my model y long range. I'm pretty sure they fit but not sure about the rear offset and center bore. These are the specs for them.

Center Bore: 66.1 mm
– PCD: 5x114.3 (5x4.5)
– Wheel Fasteners: Lug nuts
– Wheel Tightening Torque: 132 Nm
– Thread Size: M12 x 1.25

255/40ZR20 97Y 285/35ZR20 100Y
9.5Jx20 ET45 10.5Jx20 ET25

 

[N1L CO2]

Your fronts are going to look "tucked-in" with such a high offset. Adding a 12mm spacer there would take care of that though. As for the rear, that's about the max offset you want. It may even have a slight "poke". As for the center bore, you are going to need a set of hub rings to go from 66.1 down to 64.1.

 

[coloradoken]

Very

Your fronts are going to look "tucked-in" with such a high offset. Adding a 12mm spacer there would take care of that though. As for the rear, that's about the max offset you want. It may even have a slight "poke". As for the center bore, you are going to need a set of hub rings to go from 66.1 down to 64.1.

Very similar issue on some wheels I'm looking at adapting for my MY. Specifically I've a set of 18x7.5 with a 42 inset and a center bore of 72.6. The bolt pattern matches. Thoughts?

 

[coloradoken]

Very

Very similar issue on some wheels I'm looking at adapting for my MY. Specifically I've a set of 18x7.5 with a 42 inset and a center bore of 72.6. The bolt pattern matches. Thoughts?

I suppose my only real question relates to the difference between the 72.6 center bore and the Tesla center bore spec of 64.1 - is it possible to adapt that 8.5mm difference in bore size?

 

[N1L CO2]

I suppose my only real question relates to the difference between the 72.6 center bore and the Tesla center bore spec of 64.1 - is it possible to adapt that 8.5mm difference in bore size

For the much a large difference in bore size, I'd recommend getting spacers with the difference milled onto them already. So for example, if you get a 15mm spacer with wheel studs (+matching bolt pattern) and the center bore of 64.1mm, you kill 2 birds with one stone. H&R makes very goos ones.

 

[PackMan730]

I'm planning on buying 2012-2016 gtr 10 spoke wheels for my model y long range. I'm pretty sure they fit but not sure about the rear offset and center bore. These are the specs for them.

Center Bore: 66.1 mm
– PCD: 5x114.3 (5x4.5)
– Wheel Fasteners: Lug nuts
– Wheel Tightening Torque: 132 Nm
– Thread Size: M12 x 1.25

255/40ZR20 97Y 285/35ZR20 100Y
9.5Jx20 ET45 10.5Jx20 ET25

Did you ever get this done? Send some pics bruh

 

[Herroweric]

They will fit. I ran the BE wheels with no spacers and just hubcentric rings. I would probably add a spacer up front (10-15mm) for a better overall stance depending how low you are and what tire size you run.

 

[GeezerSquid]

Center Bore: 66.1 mm
– PCD: 5x114.3 (5x4.5)
– Wheel Fasteners: Lug nuts
– Wheel Tightening Torque: 132 Nm
– Thread Size: M12 x 1.25

Aren't the lugs on Model Y M14's. Will you have to bore out the new rims?

 

[Bzyrice]

I want to know this also!

 

[N1L CO2]

You will need to bore-out the lug holes to fit the wheels to the Y. Also, the rear offset may be too aggressive for a 10.5 wide wheel. You might see a slight poke.

 

[jesse_le]

I would say the rear is pretty aggressive - I run a 22x10.5 ET +40 and its pretty flush with the fender and under hard compression, it rubs on the inner fender trim lip.

 

[Jdmoto]

I would say the rear is pretty aggressive - I run a 22x10.5 ET +40 and its pretty flush with the fender and under hard compression, it rubs on the inner fender trim lip.

Whats your tire size?

 

[jesse_le]

@Jdmoto - on the rear I run a 285/35/22. I should also mention I'm lowered on MPP coilovers and MPP camber arms adjusted to factory spec.