Has anyone used Toolbox on the Model S Plaid? I bought the subscription for it but can't find any information about how to physically connect it to the car. The 2 pin diagnostic connector in the center console looks different than previous Model S.
You can install our site as a web app on your iOS device by utilizing the Add to Home Screen feature in Safari. Please see this thread for more details on this.
Note: This feature may not be available in some browsers.
Thank you for confirming. Does anyone have a part # or information regarding this Tesla interface box? There is zero information regarding it on the Tesla service manual or Toolbox help documents. They sure didn't have a problem taking my 2G for a scan tool subscription though!Correct it’s changed as you kite and I believe there’s now a Tesla specific box required to communicate with the car on these refreshes
That's funny you posted that, because I ordered the exact stuff yesterday. I'll receive it today and let everyone know if it works or not for connecting to Toolbox.This is broad-reach gigabit ethernet over a H-MTD single connector. You'd need something like this: 100-1000BASE-T1 MediaConverter H-MTD Connector
And cable:
Connecting cable 1 port 2 meters H-MTD
Buy now Connecting cable 1 port H-MTD: Connecting measurement equipment with Automotive ECUs. 100BASE-T1 & 1000BASE-T1.technica-engineering.de
Haven't tested those, but they seem like they might work. Let me know if someone gives this a shot!
I just tried this today. It works! It Gives full Toolbox access with Service Mode Plus. Model S Refresh is indeed 1000Base-T1.This is broad-reach gigabit ethernet over a H-MTD single connector. You'd need something like this: 100-1000BASE-T1 MediaConverter H-MTD Connector
And cable:
Connecting cable 1 port 2 meters H-MTD
Buy now Connecting cable 1 port H-MTD: Connecting measurement equipment with Automotive ECUs. 100BASE-T1 & 1000BASE-T1.technica-engineering.de
Haven't tested those, but they seem like they might work. Let me know if someone gives this a shot!
What is available for a user too do with this level of access?I just tried this today. It works! It Gives full Toolbox access with Service Mode Plus. Model S Refresh is indeed 1000Base-T1.
This is broad-reach gigabit ethernet over a H-MTD single connector. You'd need something like this: 100-1000BASE-T1 MediaConverter H-MTD Connector
And cable:
Connecting cable 1 port 2 meters H-MTD
Buy now Connecting cable 1 port H-MTD: Connecting measurement equipment with Automotive ECUs. 100BASE-T1 & 1000BASE-T1.technica-engineering.de
Haven't tested those, but they seem like they might work. Let me know if someone gives this a shot!
View about 2000 data parameters. Activate Service Plus mode. Run a couple hundred different service routines.What is available for a user too do with this level of access?
How do you activate service plus? I’m working in toolbox now, trying to figure it all out.View about 2000 data parameters. Activate Service Plus mode. Run a couple hundred different service routines.
Look under "Actions" then there is a line for Enable Service Mode Plus. Select it, then press run.How do you activate service plus? I’m working in toolbox now, trying to figure it all out.
Hello, can you help me. I dont know how to connect.I just tried this today. It works! It Gives full Toolbox access with Service Mode Plus. Model S Refresh is indeed 1000Base-T1.
Hello, can you help me. I dont know how to connect.
Make sure to set your laptop IP address to 192.168.90.125 and enable insecure connections on your browser. Feel free to PM me.
Unfortunately, that's all I see too. Only ETH bus and vitals.Were you able to obtain CAN information from toolbox 3? I can see vitals, but it's not really that filled out. There's also the can viewer in service mode plus, but only the ETH bus was available for me.