You can install our site as a web app on your iOS device by utilizing the Add to Home Screen feature in Safari. Please see this thread for more details on this.
Note: This feature may not be available in some browsers.
Hi,
In answer to #916's (MortenBN1988 ) on this thread, I have had a hood alignment issue after fitting the frunk kit. And, the kit worked the first time, however..., once the hood was closed, the front left side of the hood was ~4mm lower than the car bodywork and the front right side was about ~4mm higher than the car's bodywork.
After making some adjustments to the latch mechanism and to the length of the Hannshow soft close 'wire', there was little, if any, difference. So, I then disconnected the electrical supplies to the control unit and, also, detached the Hannshow strut from the hood on the side sitting higher and then manually closed it and had perfect alignment - the hood was level to the bodywork all round.
So, I'm wondering if the struts are not calibrated/one and maybe tone strut is not fully retracting leaving the hood higher at the associated front edge or something...
Has anybody else had similar issues, and, is so, how did you manage to resolve them?
Model 3 Frunk Controller Upgrade to V3 | HansshowHas anyone ordered the new $519 Frunk model that supports closing the frunk from the Tesla Nav Display and has an option foot sensor? Wanna see how that works, that has been of interest to me for some time. Although if I am in my car can someone else swipe their foot under my frunk and open it? If I don't look up quick my view is going to be blocked by the hood. I won't know if they are stealing stuff from it and running or what is going on.
Does anyone know if there is a way to upgrade an older model?
Has anyone ordered the new $519 Frunk model that supports closing the frunk from the Tesla Nav Display and has an option foot sensor? Wanna see how that works, that has been of interest to me for some time. Although if I am in my car can someone else swipe their foot under my frunk and open it? If I don't look up quick my view is going to be blocked by the hood. I won't know if they are stealing stuff from it and running or what is going on.
Does anyone know if there is a way to upgrade an older model?
Frunk...
Mightve just been me but this cost me a hour plus as pondered wtf i did wrong.....the "motor plug" is on the drivers side. There is an identical plug on the passenger side and they do not have the same trigger. The behavior is it wouldnt power open but would power down an lock/unlock.
bondoz
After placing my order for the new V3 Frunk setup with kick-sensor I was contacted saying that all I needed to pay for was cables and a card, not the new control box, so they are refunding me $14 (out of the $59 I paid). This should be interesting.
I do have TF cards to do the upgrade with, but they are sending me one along with the reader to hook to my computer. Perhaps they have had problems with different readers or cards. Either way, cannot wait to open the Frunk w/o getting in or opening the app. Just walk up and kick it sounds like.
After placing my order for the new V3 Frunk setup with kick-sensor I was contacted saying that all I needed to pay for was cables and a card, not the new control box, so they are refunding me $14 (out of the $59 I paid). This should be interesting.
I do have TF cards to do the upgrade with, but they are sending me one along with the reader to hook to my computer. Perhaps they have had problems with different readers or cards. Either way, cannot wait to open the Frunk w/o getting in or opening the app. Just walk up and kick it sounds like.
As you say, the website is changing all the time, perhaps when I ordered they had changed the price on the box to the $59 I paid ($128 total). The cable and the card are a memory card for upgrading the control box and the cable is likely for plugging the card into a computer, to put the update onto the card. I would think it's cheaper to just email the update and let me put it on my own card with my own connector, so perhaps they don't have a reader on the controller and you just plug the reader cable into the controller via USB, I don't know, but if that's the case I may leave the USB plugged in and route it into the frunk so I don't have to take the whole thing apart each time an update is released.How did you pay $59
Hey Buddy, are you saying those wires can be mistakenly installed? I thought all the wires only go in one way. My frunk power closes, but when I try to open it, it comes down right away--power opens for like a inch. Having read this thread since page 30, you're the closest one with my problem. I just got it yesterday, so presume my software is updated.
I think the wires that they are sending are for connecting the control box to the SD Card used for upgrading.