Hi everyone, just finished installing the DIY (New Version) in my 2023 M3 RWD LFP. Here are my notes that I definitely think will be helpful and useful for those trying to find what limited information that is out there:
- More for personal comfort, but be sure to bring a kneepad or something for your knees. A majority of your time will be spent contorting yourself in weird positions to be able to see the wiring. Being gloves, a flashlight (if you have a clip on / headlamp, even better), and a flat-nosed screwdriver (needed to remove some of the connectors - the white connector with black frame around it needs a screwdriver to undo the latch)
- When you begin, bear in mind that the lower trim piece is
two pieces. I almost started trying to take the whole bottom off before by accident I realized just the section with the push-pins (there are 4 on mine) is separate and definitely easier to take off. The bigger section (you can tell it has the 3 "slots" alongside the seam that implies you just need to jam your pry tool in there and push to get it to come out. It doesn't.). Also, the push pins you can easily pop open just by using the forked-end of the pry tool. The pins themselves sometimes can pop right out of the "Expanding" part of the push pin. You can just pop them back in, they're not broken.
- The very LONG side trim piece that runs along the doorsill - you don't necessarily have to completely remove this, as it has some give and rotates slightly. I could not remove the triangular panel that sits to the right of the glovebox in order to move the OTHER rectangular trim to gain access to the push pin to remove the entire long side trim piece - the triangular panel had a clip that just didn't want to come out and I was getting scared of damaging the car if I just YANKED really hard.
- The long side trim piece has two plastic "flaps" that slip under the firewall/carpeting towards the right side of the footwell. They help to keep it flush. Be aware of these flaps when rotating/removing the trim piece.
- Removing/installing/connecting the first 2 of 3 parts (the "main" connector and the side connector with the black locking brace) isn't *too* hard, it just is a little hard to get to. The side connector hides behind the long side trim piece, if you are having trouble locating it. It definitely helps to have small fingers...
- Connecting the last connector by the B pillar is slightly more challenging. Some things to note is that it helps to remove the rubber sealing/trim - you can just pull and it comes off. You can easily put it back on. The blue connector is hidden underneath a white connector plug. You can lift the B pillar trim slightly, but just try to not pull it too hard.
- The white plastic cable guide that hides underneath the door sill has a few triangular "slots" that you can push a flat nosed screwdriver into and push to release the latches so you can remove it. It helps a lot to get to the blue connector.
- The most
difficult part of the entire process, at least for me, was trying to find a way how to "hide" the frequency cutoff hardware that is built into the cable. I ended up being able to wedge it underneath the long side trim piece. That, and trying to hide/safely cable manage the extra connectors/cable girth putting the long side trim piece back.
In the end, after installation and cleanup, everything looks perfectly fine. There is a
slight bulge where the long side trim piece meets the B pillar, and I believe that is due again to the size of the frequency cutoff hardware built into the cable.
Once installation is complete, I tested everything and all the speakers work! Some observations with the speakers on:
- The additional speakers make the sound feel literally like it is coming from a sound source that is physically higher. This of course makes sense, since the speakers are more above you. Before, the sound felt like it came from somewhere waist level. Now it feels more like the sound is coming from shoulder level.
- The speakers, being mid-range and tweeters, help to add a little clarity and expanded sound stage. Previously, the stock sound sounded very much like the speakers were directly in front of you. Now, they sound like the speakers are placed a little further apart from each other.
- The alerts don't sound any louder with the new speakers on. I have Joe Mode on, and it sounds the same to me.
- Bass sounds the same, as it should.
All in all, this process took me about two hours. Mostly because I have never done something like this and am DEFINITELY not a DIY person. Took everything slowly and being my *only* car, and a *Brand new* car at that, I was extremely terrified. I would recommend that if you are patient, take your time, and want to add more ... "spatialness" to your sound, then do it. The improvement is ... not mind-blowing - it is more subtle.
If anyone has any questions, I would be more than happy to answer them. I apologize that I did not take any photos, but would definitely recommend the following video - watched it a million times before doing myself to make sure I knew the process. I apologize if I am being very wordy here, but I just want to put out as much detail as I can for those that are on the fence about doing it or can't find any helpful info.
-
(One thing to note about this is that he is working on an older model. As I mentioned earlier, the first piece you need to remove is
not the piece that has the 3 slits/slots. It is further back, and has the actual push-pin holes. Also, this video is for a different installation involving adding rear speakers, and uses a
different main connector. The Hansshow one uses the main connector
above the one used in this video )