Vendor Official Signature Wheel Gallery | Fitment Q&A Thread

[SignatureSales]

I'm just going to Dremel my holes...
I guess now all aftermarket wheel for Tesla done wrong and repeat each other.
So it's an opportunity for Signature to improve it.

Thanks again for your feedback. After discussing with our engineer, the lug hole size will be slightly increase for all Tesla wheels.

We have sold many sets of wheel and been in the Motorsport event for many years. ( Ford Motorsport, Lotus Cup championship, and Pike peak hill climb etc...) didn’t mention we own two model 3 for measurement purpose. Our measurement, and machining are precise and consistent. However, after speaking to some owners, we found out that some Model 3 has an inconsistent stud. Since our wheel are machined with minimal tolerance, any slight deformation of the stud will cause the wheel hard to mount and remove. We know it’s not easy to measure the straightness of the stud, therefore by increasing the lug hole, it will be a lot easier to mount and remove the wheel.

 

[SignatureSales]

Precision Series SV707
• Sahara Brushed Sand
• 19x9.5
• 19x9.5
Square with staggered offset setup
Lowered on @MountainPass Coilover

 

[SignatureSales]

Precision Series SV703
• Matte Black
• 19x8.5
• 19x8.5
Square with staggered offset setup
Flush front & Rear fitment and deep concave with minimal range loss

 

[NOLADriver]

LOL.....Tesla's studs are machined wrong. There is a new one. Gotta be the studs, cant be the wheels 2mm of clearance.

Meh, at least you are fixing the problem...Good job.

 

[SignatureSales]

Monobloack Series SV104
• Brushed Bronze Tinted
• 20x9
• 20x10.5
Bagged setup (no fender roll needed)

 

[SignatureSales]

Limit time only.
Buy a set and get a set of tire for $500. (Limited to two packages below, different package also available upon request) (Includes TPMS, Mount and balance, shipping)
--lower 48 states only--

Tesla Track package weight
20x9 w/ 245-35R20 Michelin PS4S

Signature Street&Track Package
20x9 w/ 245-35R20 Michelin PS4S
(44.1lb)

Signature Track Package
19x9.5 w/ 265-35R19 Bridgestone RE-71R
(~47.8lb)

​

 

[t00shay]

So tempting. Could I get a quote for sv902 20x8.5 and 20x10 with mps4s 245/285 for m3p please. Also, could I use the project kics m14 lug nuts?

 

[Cipe]

Precision Series SV703
• Matte Black
• 19x8.5 ET24
• 19x8.5 ET15
Square with staggered offset setup
Flush front & Rear fitment and deep concave with minimal range loss
View attachment 530089​

I like the look of these. I'm lowered 2" on MPP coilovers with -1.1 camber all around. I'd like to get these in 20x9 up front and 20x10.5 in the rear. Do you offer those sizes with the SV703? What offsets would you recommend to get me evenly flush front and rear. I will probably run a 245/35 up front and a 285/30 in the rear unless you recommend otherwise. I like the wheels on my cars to be as flush as possible without rubbing of course.

Also, do you happen have any photos of these on a model 3. I'm looking for gloss black on a red car specifically but will take any if you have them to see how they look. Thanks.

 

[SignatureSales]

I like the look of these. I'm lowered 2" on MPP coilovers with -1.1 camber all around. I'd like to get these in 20x9 up front and 20x10.5 in the rear. Do you offer those sizes with the SV703? What offsets would you recommend to get me evenly flush front and rear. I will probably run a 245/35 up front and a 285/30 in the rear unless you recommend otherwise. I like the wheels on my cars to be as flush as possible without rubbing of course.

Also, do you happen have any photos of these on a model 3. I'm looking for gloss black on a red car specifically but will take any if you have them to see how they look. Thanks.

Yes, the wheel is fully custom build. I've send you a quote with some options, please check.

 

[SignatureSales]

That’s right, stock width with flush front and rear fitment without spacer, and deep concave

Precision Series SV703
• Matte Black
• 19x8.5 ET24
• 19x8.5 ET15

 

[Murattukaalai]

That’s right, stock width with flush front and rear fitment without spacer, and deep concave

Precision Series SV703
• Matte Black
• 19x8.5 ET24
• 19x8.5 ET15
View attachment 533817 View attachment 533818 View attachment 533819​

do you have full car image from the back?

 

[SignatureSales]

do you have full car image from the back?

I’ll request some more pic from the owner.

 

[SignatureSales]

Clean and Simple

Monobloack Series SV104
• Brushed Bronze Tinted
• 20x9
• 20x10.5

 

[Hayden]

Tire specs?

 

[SignatureSales]

Tire specs?

235/35/20 & 275/30/20

 

[SignatureSales]

Snake action shot.

Monobloack Series SV104
• Brushed
• 20x9 (245/35/20)
• 20x10.5 (285/30/20)

 

[derichio02]

Email Sent!

 

[TwoK4drSi]

That’s right, stock width with flush front and rear fitment without spacer, and deep concave

Precision Series SV703
• Matte Black
• 19x8.5 ET24
• 19x8.5 ET15
View attachment 533817 View attachment 533818 View attachment 533819​

This is badass in terms of best in all worlds. Deeper concavity, low ET, efficiency, and stance. Is there another model you can replicate in this?

 

[SignatureSales]

This is badass in terms of best in all worlds. Deeper concavity, low ET, efficiency, and stance. Is there another model you can replicate in this?

We can build this best in all worlds setup on all model.

 

[SignatureSales]

Good looking 18” setup #meatlover

Track Series SV502
• Matte Black
• 18x9.5 (265/40/18)